Chung Metal Manufacturer & Suppliers in Da Nang, Vietnam, supplies Titanium Grade 9 Bars and Rods that are suitable for uses where strength, formability, and corrosion resistance need to be balanced. Grade 9 is a nearly-alpha titanium alloy best suited for aerospace, auto, and marine uses. Our products are produced under strict quality procedures to achieve high mechanical properties, close tolerances, and metallurgical homogeneity. With the ability to supply finished and cut-to-size rods, Chung Metal serves critical markets with performance-grade titanium lighter than steel but more powerful than commercially pure titanium and providing both strength and corrosion resistance in one alloy.
Titanium Grade 9 (Ti-3Al-2.5V) contains ~3% aluminum and ~2.5% vanadium, with the balance of titanium. This near-alpha alloy has better strength-to-weight ratio than the pure grades. Tensile strength is around 620–720 MPa, yield strength ~530–620 MPa, and elongation is ~15–20%. Hardness is between 160–180 HB. Its density is around 4.48 g/cm³. It has good weldability and corrosion resistance, especially in marine and chlorinated environments. Grade 9 is used where weight loss and moderate strength are needed, along with maintaining superior corrosion resistance.
| Grade | GRADE 9 TITANIUM ROUND BAR |
|---|---|
| Grade 9 Titanium Square bar size | 4 to 100mm |
| Titanium Grade 9 Hollow Bar | 32mm OD x 16mm ID to 250mm OD x 200mm ID) |
| Grade 9 Titanium Alloy Hex Bar size | 2-100mm A/F |
| Grade 9 Titanium Angle bar size | 3mm*20mm*20mm~12mm*100mm*100mm |
| Titanium Grade 9 Rectangles Size | 33 x 30mm to 295 x 1066mm |
| Grade 9 Titanium Alloy Flat bar size | Thickness: 2 -100mm |
| Width: 10 to 500mm | |
| Grade 9 Titanium Channel Bar | 80 x 40mm to 150 x 75mm section; 5.0 to 6.0mm thickness |
| Titanium Grade 9 Section | 3.0 to 12.0mm thickness |
| Grade 9 Titanium Alloy Round bar size | Diameter: 3-~800mm |
| Grade 9 Titanium Billet Size | 1/2″ to 495mm Diameter |
| Titanium Grade 9 Round Bar Standard Dimensions | Diameter / Height: |
| Grade 9 Titanium Surface | Bright, Hot Rolled Pickled, Cold Drawn, Sand Blasting Finished, Polished, Hairline |
| Titanium Grade 9 Tolerance | H8, H9, H10, H11, H12, H13K9, K10, K11, K12 or as per clients’ requirements |
| Grade 9 Titanium Alloy Technique | Grade 9 Titanium Hot Rolled, Cold Drawn, Cold Rolled, Forged Round Bar, Rod |
| Grade 9 Titanium Condition | Hardened & tempered, annealed |
| Finish | Cold (bright) drawn, centreless ground, hot rolled, smooth turned, peeled, slit rolled edge, hot rolled annealed, Rough Turned, Bright, Polish, Grinding, Centreless Ground & Black |
| Form | Grade 9 Titanium Round, Rod, T-Bar, Nickel Alloy Channel Bar, Precision Ground Bar, Nickel Alloy Flat Bar, Nickel Alloy Square Bar, Nickel Alloy Blocks, Nickel Alloy Round Rod, Nickel Alloy Rings, Nickel Alloy Hollow, Nickel Alloy Triangle, Rectangle, Hex (A/F), Nickel Alloy Threaded, Half Round Bar, Profiles, Nickel Alloy Billet, Nickel Alloy Ingot, I/H Bar, Forging etc. |
| Processing | Bar cutting to 650mm |
| Our Grade 9 Titanium Round bar conforms to NACE MR0175/ISO 15156 | |
| STANDARD | WERKSTOFF NR. | UNS |
| Titanium Gr. 9 | 3.7195 | R56320 |
| Grade | C | N | O | H | Ti | Fe | Al | Pd |
| Titanium Gr 9 | .08 max | .03 max | .25 max | .015 max | Bal | 0.30 max | – | .12 – .25 |
| Tensile Strength | Yield Strength (0.2%Offset) | Elongation |
| 620 | 520 | 15 % |
| Physical Properties | Metric | English |
|---|---|---|
| Density | 4.48 g/cc | 0.162 lb/in³ |
| Type | SIZES (mm) | SIZES (Inches) | ISO Tolerance |
|---|---|---|---|
| Cold Drawn and Ground | 10.00 – 75.00 | 5/6″ – 2.50″ | h8-h9-h10-h11 |
| Peeled and Polished | 40.00 – 150.00 | 1.50″ – 6.00″ | h11, h11-DIN 1013 |
| Peeled and Ground | 20.00 – 50.00 | 3/4″ – 2.00″ | h9-h10-h11 |
| Cold Drawn and Polish | 3.00 – 75.00 | 1/8″ – 3.00″ | h8-h9-h10-h11 |
Grade 9 Titanium Bars Standard lengths of 2000 mm up to 6000 mm. Cut to size on request (tolerance +2/-0 mm).
| 5.0 | 45.0 |
| 6.0 | 50.0 |
| 7.0 | 55.0 |
| 8.0 | 60.0 |
| 9.0 | 65.0 |
| 10.0 | 70.0 |
| 12.0 | 75.0 |
| 16.0 | 80.0 |
| 20.0 | 90.0 |
| 25.0 | 100.0 |
| 30.0 | 130.0 |
| 35.0 | 160.0 |
| 40.0 | 200.0 |
Yes, we provide bars and rods in standard and customized dimensions and polishes to meet your specific project requirements. For more details mail us on sales@chungmetal.com
Yes, Titanium Grade 9 Bars and Rods are suitable for hygienic and sanitary applications due to their excellent corrosion resistance, non-reactivity, and ability to withstand high temperatures, ensuring safety and durability.
Grade 9 Titanium Bars and Rods find extensive application in aerospace tubing for structural use, bike frames, motor vehicle parts, and marine fittings. They can be used for aircraft hydraulic system components, fuselage components, and racing car suspension parts due to their high strength-to-weight ratio. The corrosion resistance finds application in marine propellers, rigging, and offshore mooring systems. Grade 9 is also utilized in sporting goods including golf clubs and tennis rackets, and in industrial heat exchangers and condensers. The formability-strength balance of the alloy positions it perfectly for thin-wall pressure vessels and pipelines under aggressive service conditions.
We provide products that come with both mill test certificates and third-party test certificates, ensuring the highest standards of quality and compliance.
Chung Metals is a leading manufacturer, supplier, and exporter of high-quality bars, rods, and forgings, catering to various industries in Da Nang, Vietnam
Copyright 2024 Chung Metals. All rights reserved
